
Science exhibition season is here, and a working model that runs all day is the surest way to impress the judges.
From simple circuits to sensor alarms and Arduino builds, we’ve picked 25 working models for Class 6 to 10, each with its concept, cost band and ready-to-order parts list.

How to Pick a Model Judges Remember
Choose a science exhibition working model that runs reliably on battery for hours, because judges walk past all day. Best picks: Class 6–7: solar fan, electromagnet crane, lemon battery. Class 8–9: automatic street light, rain alarm, water level indicator. Class 10: smart irrigation, touch-free sanitizer dispenser, smart stick for the blind. Most models cost about ₹80–₹550 in parts.
Jump to your section:
- Class 6–7: 8 simple working models
- Class 8–9: 9 sensor-based models
- Class 10: 8 Arduino and sensor models
- Master table: all 25 models compared
- Exhibition day checklist
The models judges remember have three things in common:
-
It actually works when they arrive.
A simple model that runs every time beats a flashy one that needs fixing. -
It explains one clear concept from the textbook.
Judges ask "what is the principle?" first, so every model below names its concept. -
It solves a real problem.
Water, safety, health and energy topics score well with judges.
Every model has a parts list with product links. Cardboard, bottles and other craft items come from home.
Looking for more ideas? See our Top 15 Sensor-Based Project Ideas for Students.
Components and Supplies
Class 6 to 7: 8 Simple Working Models
These easy science exhibition projects use batteries, LEDs, motors, and switches. No coding and no soldering: everything connects with clips and wires.
1. Conductor and Insulator Tester
Touch the two clips to a coin, eraser or pencil lead. If the LED glows, the object is a conductor.
Science concept: Metals let electric current flow through them, so they are conductors. Rubber, plastic and wood block it, so they are insulators.
Parts (Under ₹150): 2 AA Battery Holder · Red LED 5mm · Alligator Clips · 100Ω resistor
Build it in 5 steps:
- Put two AA cells in the battery holder.
- Connect the holder's red wire to the 100Ω resistor, then to the LED's long leg.
- Clip one alligator lead to the LED's short leg.
- Clip the second lead to the holder's black wire.
- Touch both free clips to each object and sort it into a Conductor or Insulator tray.
Level it up: test pencil lead, a steel spoon and aluminium foil, and rank them by how brightly the LED glows.
What to tell the judges: The LED only glows when the object completes the circuit, and that is what a conductor does.
2. Series and Parallel Circuit Board
Three LEDs in series and three in parallel, each circuit with its own switch. Remove one LED to show which circuit keeps working.
Science concept: A series circuit has one path, so one break stops every light. In a parallel circuit each LED has its own path, so the others stay on.
Parts (₹150–₹300): 9V Battery · 9V Battery Snap · Red LED 5mm · Mini Rocker Switches · Alligator Clips · 470Ω resistors
Build it in 5 steps:
- Divide a cardboard base into two halves: Series and Parallel.
- Series side: chain three red LEDs long leg to short leg, with one 470Ω resistor and a switch.
- Parallel side: give each LED its own 470Ω resistor and wire all three across the same two rails, with a switch.
- Connect both circuits to the 9V battery through the snap.
- Switch each side on, pull out one LED and compare what happens.
Level it up: add a fourth LED to each side and show that the series LEDs get dimmer while the parallel ones stay bright.
What to tell the judges: Our homes are wired in parallel, so one fused bulb doesn't switch off the whole house.
3. Solar-Powered Fan

A solar panel spins a fan with no battery. Use direct sunlight or a bright desk lamp, and keep the blade light.
Science concept: The solar panel turns light energy into electrical energy. The motor turns that into kinetic energy, the spin of the fan.
Parts (Under ₹150): Mini Solar Panel 70×70 mm · 3V DC Toy Motor · Hook-up Wire
Build it in 5 steps:
- Cut a light three-blade fan from card or a plastic bottle.
- Press the fan onto the motor shaft.
- Fix the motor on top of a cardboard stand.
- Connect the panel's two wires to the motor's two terminals.
- Tilt the panel toward sunlight or a bright desk lamp.
Level it up: cover half the panel with paper and show the fan slow down.
What to tell the judges: More light on the panel means more current, so the fan spins faster.
Prefer a ready-made build? Browse our science kits.
4. Lemon Battery
Four lemons with zinc-coated nails and copper coins, wired in series, light a red LED.
Science concept: Zinc and copper react differently with the lemon's acid, which pushes electrons through the wire. Chemical energy becomes electrical energy.
Parts (Under ₹150): Red LED 5mm · Alligator Clips
Build it in 5 steps:
- Roll four lemons on the table to release the juice.
- Push a zinc-coated (galvanised) nail and a copper coin into each lemon, about 2 cm apart.
- Clip the coin of one lemon to the nail of the next, all the way along.
- Clip the last free coin to the LED's long leg and the first free nail to its short leg.
- Dim the room lights so the glow is easy to see.
Level it up: swap the lemons for potatoes or tomatoes and compare the glow.
What to tell the judges: Each lemon makes just under 1 volt, so four in series are needed to light the LED.
5. Electromagnet Crane

Copper wire wound on an iron nail lifts pins when switched on and drops them when switched off.
Science concept: Current flowing through a coil creates a magnetic field, and the iron nail makes it stronger. Switch off the current and the magnetism disappears.
Parts (₹150–₹300): Copper Wire 28 SWG · 2 AA Battery Holder · Mini Rocker Switch · Alligator Clips
Build it in 5 steps:
- Sand 2 cm of enamel off both ends of the copper wire.
- Wind about 100 tight turns around a large iron nail.
- Connect one wire end to the battery holder through the rocker switch.
- Clip the other wire end to the holder's second lead.
- Hang the nail from a cardboard crane arm and lift paper clips. Switch off between demos so the coil stays cool.
Level it up: count the clips lifted with 50, 100 and 150 turns and show the results on a chart.
What to tell the judges: More turns or more current make a stronger magnet, and switching off drops the load, just like scrapyard cranes.
6. Rainwater Harvesting with a Working Pump

Rain from a cardboard roof fills a tank, and a mini pump lifts the stored water back to a tap.
Science concept: Collecting rainwater from roofs saves groundwater. The pump shows how stored water is lifted for use.
Parts (Under ₹150): Mini Water Pump · 2 AA Battery Holder · Mini Rocker Switch
Build it in 5 steps:
- Build a sloping cardboard roof with a gutter made from a cut pipe or straw.
- Run the gutter into a clear bottle that acts as the tank.
- Place the mini pump at the bottom of the tank and run its tube to a tap point.
- Wire the pump to the battery holder through the rocker switch.
- Pour water on the roof, then switch on the pump to empty the tank.
Level it up: add a sand-and-gravel layer at the tank inlet to show how rainwater is filtered.
What to tell the judges: A 100 m² roof can collect tens of thousands of litres in one monsoon, water that would otherwise run off.
7. Turbine Roof Ventilator Working Model

A turbine roof ventilator spins with wind and rising warm air, pulling hot air out of a building without electricity. Our model uses light card blades on a small DC motor, so the spin also makes a small voltage you can measure, showing how motion turns into electricity.
Science concept: Warm air is lighter than cool air, so it rises (convection) and pushes up through the ventilator. Wind blowing across the curved vanes adds more spin, which pulls even more hot air out from below.
Parts (₹150–₹300): 3V DC Toy Motor · Digital Multimeter · Hook-up Wire
Build it in 5 steps:
- Make a cardboard box "room" and cut a round hole in its roof.
- Cut 12 to 16 curved vanes from thin card and glue them between two card rings to form a drum.
- Fix the motor to a card bridge above the hole, shaft pointing down, and glue the drum's top to the shaft.
- Check that the drum spins freely over the hole without touching the roof.
- Blow a table fan across the vanes, or a hair dryer on low into a side hole, and watch it spin.
Measure the voltage (motor as generator): set the multimeter to the 2000mV DC range and clip its probes to the motor terminals. As the drum spins, the reading rises, and it climbs further when the wind is stronger. A red LED needs about 1.8 V, more than a breeze can produce through a direct-drive toy motor, so the meter is what proves the generator works on exhibition day. See how a DC motor works and the parts of an electric motor.
What to tell the judges: The ventilator uses no electricity: rising warm air and wind turn it, and our motor shows that the spin can be turned back into electricity.
8. Magnetic Door Alarm
A fridge magnet on a cardboard door keeps a reed switch closed. Open the door and the buzzer sounds.
Science concept: A reed switch closes when a magnet is near. When the door opens the magnet moves away, the switch opens and the transistor turns the buzzer on.
Parts (Under ₹150): Reed Switch · BC547 Transistor · Active Buzzer Module · 2 AA Battery Holder · Hook-up Wire · 10kΩ resistor
Build it in 5 steps:
- Make a cardboard door frame with a hinged door.
- Glue the reed switch to the frame and a fridge magnet to the door edge so they line up when shut.
- Wire the buzzer through the BC547 so the transistor switches it, with the 10kΩ resistor feeding the base from battery +.
- Connect the reed switch from the transistor's base to battery −, so a closed switch keeps the buzzer off.
- Close the door, insert the batteries, then open the door to test.
Level it up: add a red LED beside the buzzer so the alarm can be seen as well as heard.
What to tell the judges: A magnet and a reed switch make a contact-free sensor, the same idea used in real door and window alarms.
Want a model that moves? Try our DIY RC car kits.
Class 8 to 9: 9 Sensor-Based Models
These models add sensors, so the circuit reacts to light, water, movement or heat. Each one makes a strong working model for a Class 8 science exhibition.
9. Heart Pump Model
A mini pump circulates red "blood" between two bottle chambers, like the heart.
Science concept: The heart is a pump that pushes blood around the body in a loop. The mini pump plays the heart, and the tubes play the blood vessels.
Parts (Under ₹150): Mini Water Pump · 2 AA Battery Holder · Mini Rocker Switch
Build it in 5 steps:
- Fill one bottle with water coloured red with food colour.
- Place the mini pump inside it and run its outlet tube to a second bottle.
- Raise the second bottle and run a return tube back to the first, so water drains back.
- Wire the pump to the battery holder through the rocker switch.
- Switch on and label the parts: heart, arteries and veins.
Level it up: press the switch on and off in a steady rhythm to show a heartbeat.
What to tell the judges: Arteries carry blood away from the heart and veins bring it back, just like the two tubes here.
10. "Do Liquids Conduct Electricity?" Tester
Dip two probes into salt water, lemon juice, sugar water and oil, and compare the LED's glow.
Science concept: Liquids with dissolved salts or acids contain ions that carry current, so they conduct. Sugar water and oil barely conduct at all.
Parts (Under ₹150): 9V Battery · 9V Battery Snap · Red LED 5mm · Alligator Clips · 470Ω resistor
Build it in 5 steps:
- Connect the 9V battery's + wire to the 470Ω resistor, then to the LED's long leg.
- Clip one probe lead to the LED's short leg.
- Clip a second probe lead to the battery's − wire.
- Pour salt water, lemon juice, sugar water and oil into labelled cups.
- Dip both probes into each cup, rinsing them between tests, and compare the glow.
Level it up: with an adult present, use pencil-lead electrodes in salt water to show electrolysis bubbles.
What to tell the judges: A brighter glow means more ions in the liquid, which is why we never touch switches with wet hands.
11. Automatic Street Light

Street lamps on a cardboard road switch on when it gets dark. Cover the sensor to demonstrate.
Science concept: An LDR's resistance rises in the dark. The transistor senses that change and switches the LEDs on, like real street lights.
Parts (₹150–₹300): LDR · BC547 Transistor · Red LED 5mm · Breadboard · 9V Battery · 9V Battery Snap · Hook-up Wire · 10kΩ and 1kΩ resistors
Build it in 5 steps:
- Place the BC547 on the breadboard.
- Connect the 10kΩ resistor from + to the transistor's base, and the LDR from the base to −.
- Wire each red LED with its own 1kΩ resistor from + to the collector, and connect the emitter to −.
- Mount the LEDs on straw lamp posts along a cardboard road.
- Connect the 9V battery and cover the LDR to make it "night".
Level it up: build the Arduino version below to set the exact light level at which the lamps switch on.
What to tell the judges: No one presses a switch; the light level decides, so no electricity is wasted in daytime.
Arduino version: Smart Street Light System tutorial.
12. Water Level Indicator
LEDs light one by one as a tank fills, and a buzzer sounds when it is full.
Science concept: Tap water contains dissolved salts, so it conducts a small current. When the water reaches a wire, it switches on that level's transistor.
Parts (₹150–₹300): BC547 Transistor · Red LED 5mm · Active Buzzer Module · 2 AA Battery Holder · Breadboard · Hook-up Wire · 1kΩ and 220Ω resistors
Build it in 5 steps:
- Tape a bare wire to the bottom of a clear bottle and connect it to battery +.
- Tape three more wires at the low, middle and high levels.
- Connect each level wire through a 1kΩ resistor to the base of its own BC547.
- Wire a red LED and 220Ω resistor to the low and middle collectors, and the buzzer to the high one; emitters go to −.
- Pour water in slowly and watch the LEDs light in order.
Level it up: mark the levels as 25%, 50% and Full, and time how long the tank takes to fill.
What to tell the judges: It stops tanks overflowing, which saves both water and the electricity used to pump it.
13. Rain Alarm

A rain board on a model roof sounds a buzzer when water drops land on it. Use a spray bottle for rain.
Science concept: When dry, the board's metal tracks are not connected. Raindrops bridge them, letting current reach the transistor, which switches on the buzzer.
Parts (Under ₹150): Rain Drop Sensor · BC547 Transistor · Active Buzzer Module · 2 AA Battery Holder · 1kΩ resistor
Build it in 5 steps:
- Fix the rain board (the sensor plate) on a sloping cardboard roof.
- Connect one board terminal to battery +, and the other through the 1kΩ resistor to the BC547's base.
- Connect the buzzer from battery + to the collector, and the emitter to −.
- Tuck the battery and transistor under the roof, away from the water.
- Spray water on the board and the buzzer sounds.
Level it up: try the Arduino version below, which can also measure how heavy the rain is.
What to tell the judges: It can warn you to shut windows or cover drying crops before the rain gets heavy.
Arduino version: Simple Rain Detector Project Using Arduino.
14. Seismograph (Earthquake Alarm)
Shake the table and a hanging metal weight touches a foil ring, sounding the alarm.
Science concept: Inertia keeps the hanging weight still while the ground shakes. The frame moves around it, so the foil ring touches the weight and completes the circuit.
Parts (Under ₹150): Active Buzzer Module · 2 AA Battery Holder · Hook-up Wire · Alligator Clips
Build it in 5 steps:
- Build a cardboard stand with an arm at the top.
- Hang a metal nut from the arm on stripped hook-up wire.
- Tape a ring of foil around the nut, about 5 mm away, without touching it.
- Connect battery + to the hanging wire, and the foil ring through the buzzer to battery −.
- Shake the table gently and the buzzer sounds.
Level it up: change the gap between the nut and the ring and show which setting detects the lightest shake.
What to tell the judges: Real seismometers use the same idea: a heavy mass stays still while the Earth moves around it.
15. Hydroelectric Power Plant
Water falling from a raised bottle turns a spoon turbine on a motor, lighting a red LED.
Science concept: Water stored high up has potential energy. As it falls it gains kinetic energy, and the turbine and motor turn that into electrical energy.
Parts (Under ₹150): 3V DC Toy Motor · Red LED 5mm · Hook-up Wire · optional Mini Water Pump
Build it in 5 steps:
- Glue plastic spoons around a bottle cap to make a water wheel.
- Press the cap onto the motor shaft.
- Fix the motor beside a tray so the wheel sits under a raised bottle's outlet.
- Connect the red LED across the motor's two terminals.
- Open the bottle and let the water stream hit the spoons.
Level it up: use the mini pump to lift the water back up and reuse it, like a pumped-storage plant.
What to tell the judges: Water falling from higher up spins the wheel harder, which is why dams are built tall.
16. Simple Electric Motor

A hand-wound copper coil spins continuously above a magnet on two safety-pin supports.
Science concept: A current-carrying wire in a magnetic field feels a force (Fleming's left-hand rule). That force pushes the coil around, so it keeps spinning.
Parts (₹300–₹600): Copper Wire 28 SWG · Neodymium Magnet · 2 AA Battery Holder · Alligator Clips
Build it in 5 steps:
- Wind copper wire 15 times around a AA cell to make a coil, leaving 3 cm straight ends.
- Sand the enamel fully off one end, and off only the top half of the other.
- Stand two safety pins on a base and clip them to the battery holder.
- Place the magnet on the base, under where the coil will sit.
- Rest the coil in the pin loops and give it a gentle flick.
Level it up: flip the magnet over and show the coil spin the other way.
What to tell the judges: The half-scraped end cuts the current for half a turn, so the push always acts in the same direction.
17. AC/DC Generator
Spin a magnet inside a 200-turn coil with a hand crank, and a red LED flickers with each turn.
Science concept: A changing magnetic field through a coil creates a current. This is electromagnetic induction, the principle behind every power station.
Parts (₹300–₹600, shares the wire and magnet with #16): Copper Wire 28 SWG · Neodymium Magnet · Red LED 5mm
Build it in 5 steps:
- Wind 200 turns of copper wire around a small cardboard box.
- Push a skewer through the centre of the box as an axle.
- Glue the magnet to the axle inside the box so it spins without touching the sides.
- Sand the wire ends and connect them to the red LED.
- Turn the axle quickly with a card crank and watch the LED flicker.
Level it up: add more turns and show the LED glow brighter.
What to tell the judges: No battery is used: motion and a magnet make electricity, exactly like a power station generator.
Class 10: 8 Arduino and Sensor Models
For a Class 10 science project working model, an Arduino UNO lets students program a "sense, decide, act" loop: read a sensor, compare it with a set value, then switch something on or off. This is rule-based logic, not AI, but it is the same loop that robots and smart devices are built on.
One Arduino UNO can be reused across projects. Each needs a USB cable and a laptop to upload the code.
18. Smart Traffic Light
Red, yellow and green LEDs change in a timed sequence.
Science concept: An Arduino follows a program line by line. Here a short program switches three LEDs in a timed loop, like a traffic signal.
Parts (₹300–₹600): Arduino UNO · LED Combo 5mm · Breadboard · M2M Jumper Wires · 220Ω resistors
Build it in 5 steps:
- Place red, yellow and green LEDs on the breadboard, each with a 220Ω resistor to GND.
- Connect the LEDs' long legs to Arduino pins 11, 12 and 13.
- Write code that turns green on for 5 seconds, yellow for 2, then red for 5.
- Upload it from the Arduino IDE over USB.
- Mount the LEDs in a cardboard signal pole at a model crossing.
Arduino code:
// Smart Traffic Light - Arduino UNO
const int RED_LED = 11;
const int YELLOW_LED = 12;
const int GREEN_LED = 13;
void setup() {
pinMode(RED_LED, OUTPUT);
pinMode(YELLOW_LED, OUTPUT);
pinMode(GREEN_LED, OUTPUT);
}
void loop() {
digitalWrite(GREEN_LED, HIGH); // green for 5 seconds
delay(5000);
digitalWrite(GREEN_LED, LOW);
digitalWrite(YELLOW_LED, HIGH); // yellow for 2 seconds
delay(2000);
digitalWrite(YELLOW_LED, LOW);
digitalWrite(RED_LED, HIGH); // red for 5 seconds
delay(5000);
digitalWrite(RED_LED, LOW);
}
Level it up: add a second set of LEDs for the crossing road and keep the two signals in sync.
What to tell the judges: Changing one delay value in the code changes the timing, which is how real signals are tuned for traffic.
19. Clap Switch
Clap once to switch a light on, and again to switch it off.
Science concept: The sound sensor's microphone turns the vibration of a clap into an electrical signal. The Arduino reads that signal and toggles the light.
Parts (₹300–₹600): Arduino UNO · Sound Sensor Module · Red LED 5mm · 220Ω resistor · Breadboard · M2F Jumper Wires
Build it in 5 steps:
- Connect the sound sensor's VCC, GND and DO pins to Arduino 5V, GND and pin 2.
- Wire the red LED and 220Ω resistor on the breadboard to pin 13.
- Write code that flips the LED each time pin 2 goes HIGH, with a short delay to ignore echoes.
- Upload, then turn the sensor's screw until only claps trigger it.
- Fit the LED inside a cardboard lamp.
Arduino code:
// Clap Switch - Arduino UNO
const int SOUND_PIN = 2; // sound sensor DO pin
const int LED_PIN = 13; // LED through 220 ohm resistor
bool ledState = false;
void setup() {
pinMode(SOUND_PIN, INPUT);
pinMode(LED_PIN, OUTPUT);
}
void loop() {
// Most modules give HIGH on a loud sound.
// If yours gives LOW, change HIGH to LOW below.
if (digitalRead(SOUND_PIN) == HIGH) {
ledState = !ledState; // flip the light
digitalWrite(LED_PIN, ledState);
delay(500); // ignore echoes
}
}
Level it up: count claps, so two claps switch the light on and three switch it off.
What to tell the judges: The sensor turns sound into electricity, the same principle a phone microphone uses.
20. Temperature-Controlled Fan
A fan switches on by itself when the room heats up. Demonstrate with a hair dryer.
Science concept: A thermistor's resistance changes as it heats up. The Arduino reads that change and switches a relay, which turns the fan on.
Parts (₹300–₹600): Arduino UNO · Thermistor Module · 5V Relay · 3V DC Toy Motor · 2 AA Battery Holder · M2F Jumper Wires
Build it in 5 steps:
- Connect the thermistor module's VCC, GND and AO pins to 5V, GND and A0.
- Connect the relay's VCC, GND and IN pins to 5V, GND and pin 7.
- Wire the motor and AA holder through the relay's COM and NO terminals.
- Write code that switches the relay on when the A0 reading passes a set level.
- Fit a card fan on the motor and warm the sensor with a hair dryer.
Arduino code:
// Temperature-Controlled Fan - Arduino UNO
const int SENSOR_PIN = A0; // thermistor module AO pin
const int RELAY_PIN = 7; // relay IN pin
const int THRESHOLD = 600; // set this after watching the Serial Monitor
void setup() {
pinMode(RELAY_PIN, OUTPUT);
digitalWrite(RELAY_PIN, LOW);
Serial.begin(9600);
}
void loop() {
int reading = analogRead(SENSOR_PIN);
Serial.println(reading); // watch the value rise or fall with heat
// If your reading FALLS as it gets hotter, change > to <.
// If your relay is active-LOW, swap HIGH and LOW below.
if (reading > THRESHOLD) {
digitalWrite(RELAY_PIN, HIGH); // fan ON
} else {
digitalWrite(RELAY_PIN, LOW); // fan OFF
}
delay(500);
}
Level it up: print the temperature readings on the Serial Monitor so visitors can watch them rise.
What to tell the judges: The fan runs only when it is needed, which saves energy.
21. Smart Irrigation System

When the soil dries out, the Arduino switches on a pump, and stops it when the soil is moist.
Science concept: Wet soil conducts electricity better than dry soil. The Arduino reads the moisture level and switches the pump through a relay.
Parts (₹300–₹600): Arduino UNO · Soil Moisture Sensor · 5V Relay · Mini Water Pump · Jumper Wire Set · 2 AA Battery Holder
Build it in 5 steps:
- Push the soil moisture probe into a potted plant.
- Connect the sensor's VCC, GND and AO pins to 5V, GND and A0.
- Connect the relay's IN pin to pin 7, and wire the pump and battery holder through the relay.
- Write code that switches the pump on when the soil reads dry and off when it reads moist.
- Put the pump in a water container and run its tube to the base of the plant.
Arduino code:
// Smart Irrigation System - Arduino UNO
const int MOISTURE_PIN = A0; // soil moisture sensor AO pin
const int RELAY_PIN = 7; // relay IN pin (controls the pump)
const int DRY_LEVEL = 600; // higher reading = drier soil; tune this
void setup() {
pinMode(RELAY_PIN, OUTPUT);
digitalWrite(RELAY_PIN, LOW);
Serial.begin(9600);
}
void loop() {
int moisture = analogRead(MOISTURE_PIN);
Serial.println(moisture); // use these readings for your chart
// If your relay is active-LOW, swap HIGH and LOW below.
if (moisture > DRY_LEVEL) {
digitalWrite(RELAY_PIN, HIGH); // soil is dry: pump ON
} else {
digitalWrite(RELAY_PIN, LOW); // soil is moist: pump OFF
}
delay(1000);
}
Level it up: log the moisture readings over a day and show the chart beside the model.
What to tell the judges: Plants get water only when they need it, which can save a lot of water on farms.
22. Touch-Free Hand Sanitizer Dispenser

An IR sensor detects a hand and runs the pump for a moment. Use coloured water, since sanitizer is flammable.
Science concept: The IR sensor sends out infrared light. A hand reflects it back, and the Arduino runs the pump for a moment.
Parts (₹300–₹600): Arduino UNO · IR Sensor · 5V Relay · Mini Water Pump · 2 AA Battery Holder · M2F Jumper Wires
Build it in 5 steps:
- Connect the IR sensor's VCC, GND and OUT pins to 5V, GND and pin 2.
- Connect the relay's IN pin to pin 7, and wire the pump and battery holder through it.
- Write code that runs the pump for half a second when a hand is detected, then waits.
- Put the pump in a bottle of coloured water and run the tube to a nozzle.
- Mount the sensor under the nozzle, pointing down, and adjust its range screw.
Arduino code:
// Touch-Free Hand Sanitizer Dispenser - Arduino UNO
const int IR_PIN = 2; // IR sensor OUT pin
const int RELAY_PIN = 7; // relay IN pin (controls the pump)
int useCount = 0;
void setup() {
pinMode(IR_PIN, INPUT);
pinMode(RELAY_PIN, OUTPUT);
digitalWrite(RELAY_PIN, LOW);
Serial.begin(9600);
}
void loop() {
// Most IR modules give LOW when a hand is detected.
if (digitalRead(IR_PIN) == LOW) {
digitalWrite(RELAY_PIN, HIGH); // pump ON for half a second
delay(500);
digitalWrite(RELAY_PIN, LOW);
useCount++;
Serial.print("Uses: ");
Serial.println(useCount);
delay(1000); // wait before the next dispense
}
}
Level it up: count each use and show the total on the Serial Monitor.
What to tell the judges: Touch-free means germs aren't passed from hand to hand through a shared pump.
23. Smart Stick for the Visually Impaired
An IR sensor on a walking stick beeps when an obstacle is within about 30 cm.
Science concept: The IR sensor detects light reflected from nearby obstacles, and the Arduino turns that into a beep the user can hear.
Parts (₹300–₹600): Arduino UNO · IR Sensor · Active Buzzer Module · M2F Jumper Wires · 9V Battery · 9V Battery Snap
Build it in 5 steps:
- Tape the IR sensor near the bottom of a walking stick, facing forward.
- Connect its VCC, GND and OUT pins to 5V, GND and pin 2.
- Connect the buzzer to pin 8 and GND.
- Write code that sounds the buzzer when the sensor detects an obstacle.
- Power the Arduino from the 9V battery through the snap, to VIN and GND.
Arduino code:
// Smart Stick for the Visually Impaired - Arduino UNO
const int IR_PIN = 2; // IR sensor OUT pin
const int BUZZER_PIN = 8; // active buzzer
void setup() {
pinMode(IR_PIN, INPUT);
pinMode(BUZZER_PIN, OUTPUT);
}
void loop() {
// Most IR modules give LOW when an obstacle is detected.
if (digitalRead(IR_PIN) == LOW) {
digitalWrite(BUZZER_PIN, HIGH); // beep
} else {
digitalWrite(BUZZER_PIN, LOW);
}
delay(50);
}
Level it up: add a second sensor higher up to warn about waist-level obstacles.
What to tell the judges: It warns the user before the stick even touches the obstacle.
24. Fire Alarm
A heat sensor in a model house sounds the alarm when the temperature rises.
Science concept: A thermistor's resistance changes with heat. When the reading crosses a set level, the Arduino sounds the buzzer.
Parts (₹300–₹600): Arduino UNO · Thermistor Module · Active Buzzer Module · M2F Jumper Wires · optional Flame Sensor
Build it in 5 steps:
- Build a cardboard model house and fix the thermistor module under the roof.
- Connect the module's VCC, GND and AO pins to 5V, GND and A0.
- Connect the buzzer to pin 8 and GND.
- Write code that sounds the buzzer when the A0 reading passes a threshold.
- Test with a hair dryer, never a real flame.
Arduino code:
// Fire Alarm - Arduino UNO
const int SENSOR_PIN = A0; // thermistor module AO pin
const int BUZZER_PIN = 8; // active buzzer
const int THRESHOLD = 600; // set this after watching the Serial Monitor
void setup() {
pinMode(BUZZER_PIN, OUTPUT);
Serial.begin(9600);
}
void loop() {
int reading = analogRead(SENSOR_PIN);
Serial.println(reading);
// If your reading FALLS as it gets hotter, change > to <.
if (reading > THRESHOLD) {
digitalWrite(BUZZER_PIN, HIGH); // alarm ON
} else {
digitalWrite(BUZZER_PIN, LOW);
}
delay(200);
}
Level it up: add the flame sensor so the alarm also reacts to the light from a fire.
What to tell the judges: Heat alarms give people time to get out, and this model shows how the sensing works.
Full wiring and code: Fire Alarm System Using Arduino.
25. Smart Home Security System
A reed switch guards the door and an IR sensor guards the window; either one sets off the alarm.
Science concept: Two sensors watch different entry points, and the code uses OR logic: if either one is triggered, the alarm sounds.
Parts (₹300–₹600): Arduino UNO · Reed Switch · IR Sensor · Active Buzzer Module · M2F Jumper Wires
Build it in 5 steps:
- Fix the reed switch on a cardboard door frame and a fridge magnet on the door.
- Connect the reed switch between pin 3 and GND, using the Arduino's internal pull-up.
- Mount the IR sensor at the window and connect it to 5V, GND and pin 2.
- Connect the buzzer to pin 8 and GND.
- Write code that sounds the buzzer if the door opens OR the window sensor detects movement.
Arduino code:
// Smart Home Security System - Arduino UNO
const int WINDOW_IR_PIN = 2; // IR sensor OUT pin (window)
const int REED_PIN = 3; // reed switch between pin 3 and GND (door)
const int BUZZER_PIN = 8; // active buzzer
void setup() {
pinMode(WINDOW_IR_PIN, INPUT);
pinMode(REED_PIN, INPUT_PULLUP); // internal pull-up resistor
pinMode(BUZZER_PIN, OUTPUT);
}
void loop() {
// Door shut: magnet closes the reed switch, so the pin reads LOW.
// Door open: the switch opens and the pin reads HIGH.
bool doorOpen = (digitalRead(REED_PIN) == HIGH);
// Most IR modules give LOW when movement is detected.
bool windowTriggered = (digitalRead(WINDOW_IR_PIN) == LOW);
if (doorOpen || windowTriggered) { // OR logic
digitalWrite(BUZZER_PIN, HIGH);
} else {
digitalWrite(BUZZER_PIN, LOW);
}
delay(50);
}
Level it up: add an LED for each sensor so the display shows which entry was triggered.
What to tell the judges: Combining sensors with simple logic is exactly how real smart-home alarms work.
More coding builds: 30 Simple AI Project Ideas and Top 20 Robotics Projects for Students.
Table: Model, Concept Explained, Difficulty, Parts, Time
Build times are approximate and include testing.
| # | Model | Concept explained | Difficulty | Key parts | Time |
|---|---|---|---|---|---|
| 1 | Conductor & insulator tester | Conductors vs insulators | Easy | LED, AA holder, clips | 1 hr |
| 2 | Series & parallel circuit | Circuit types | Easy | 9V battery, LEDs, switches | 1–2 hrs |
| 3 | Solar fan | Solar energy | Easy | Solar panel, DC motor | 1–2 hrs |
| 4 | Lemon battery | Chemical to electrical energy | Easy | Red LED, clips | 1 hr |
| 5 | Electromagnet crane | Magnetic effect of current | Easy | Copper wire, AA holder | 2 hrs |
| 6 | Rainwater harvesting | Water conservation | Easy | Mini pump, switch | 2–3 hrs |
| 7 | Turbine roof ventilator | Convection, wind energy | Easy | DC motor, multimeter | 2–3 hrs |
| 8 | Magnetic door alarm | Magnetism, switching | Easy | Reed switch, buzzer | 2 hrs |
| 9 | Heart pump | Blood circulation | Medium | Mini pump | 2–3 hrs |
| 10 | Liquid conductivity tester | Chemical effects of current | Easy | 9V battery, LED | 1 hr |
| 11 | Automatic street light | LDR, transistor switch | Medium | LDR, BC547 | 2–3 hrs |
| 12 | Water level indicator | Conductivity of water | Medium | BC547, buzzer | 2–3 hrs |
| 13 | Rain alarm | Water completes a circuit | Medium | Rain sensor, buzzer | 2 hrs |
| 14 | Seismograph | Inertia, vibrations | Medium | Buzzer, pendulum | 2–3 hrs |
| 15 | Hydroelectric plant | Energy conversion | Medium | DC motor, LED | 2–3 hrs |
| 16 | Simple electric motor | Force on a conductor | Medium | Copper wire, magnet | 2–3 hrs |
| 17 | AC/DC generator | Electromagnetic induction | Medium | Copper wire, magnet | 3 hrs |
| 18 | Smart traffic light | Programming logic | Medium | Arduino, LEDs | 3–4 hrs |
| 19 | Clap switch | Sound to electrical signal | Advanced | Arduino, sound sensor | 3–4 hrs |
| 20 | Temperature-controlled fan | Thermistor, relay | Advanced | Arduino, thermistor, relay | 4–5 hrs |
| 21 | Smart irrigation | Soil moisture sensing | Advanced | Arduino, soil sensor, pump | 4–6 hrs |
| 22 | Touch-free sanitizer | IR reflection | Advanced | Arduino, IR sensor, pump | 4–6 hrs |
| 23 | Smart stick | Obstacle sensing | Advanced | Arduino, IR sensor, buzzer | 3–4 hrs |
| 24 | Fire alarm | Heat detection | Advanced | Arduino, thermistor, buzzer | 3–4 hrs |
| 25 | Smart home security | Multi-sensor logic | Advanced | Arduino, reed, IR sensor | 4–5 hrs |
Exhibition Day Checklist
Most models fail on exhibition day because of power, not the idea. Run through this list the night before.
Power
- Fit fresh batteries on the morning of the exhibition, and pack one full spare set.
- Run the model continuously for 2 hours at home. If it slows down or dims, the batteries won't last the day.
- For Arduino models, a USB power bank lasts much longer than a single 9V battery.
- Never connect 3.3–5V sensor or buzzer modules directly to a 9V battery.
Backup parts
- 2–3 spare LEDs, jumper wires and alligator clips.
- A spare motor or pump for moving models (they are the parts most likely to fail).
- Tape, a glue gun stick, scissors and a small screwdriver.
- The Arduino code, saved on a pen drive or phone.
Chart
- Aim, principle (with the chapter name), labelled circuit diagram, working steps and real-life uses.
- A small parts and cost list, because judges often ask how much it cost.
- Write a 60-second explanation and practise it out loud.
Safety
- Keep water and electronics on separate levels of the model, and seal joints with tape.
- No open flames: use a hair dryer to test heat sensors.
- Electrolysis and any experiment with salt water should be done with an adult present.
Get the Parts and Start Building
Every model above comes with its own parts list and product links, so you can order everything in one go. Want a ready-made option? Shop science kits for complete solar, wind, and STEM kits.







