Skip to content
Free Delivery on Orders Above Rs 999/- Pan-India
Cash on Delivery Available for Orders above Rs.500/- and Upto Rs 3000/-
SAVE more when you BUY more. Upto 30% Off on BULK PURCHASE
GST Invoices for Your Business
Dedicated Technical Support Team
Safely Delivering Genuine Products PAN INDIA

How to Make an RC Car at Home: Parts, Wiring, & 2.4GHz Setup

How to Make an RC Car at Home: Parts, Wiring, & 2.4GHz Setup
-
Written By - Robocraze -
📅 Updated on 20 Nov 2026
✨ Summarize with AI
✅ Prompt copied

Summary

Building an RC car at home takes five parts: a chassis with steering, a geared drive motor, an ESC, a steering servo and a 3S LiPo. This guide pairs them with a FlySky FS-GT2 2.4GHz transmitter and receiver, covers wiring, binding, battery safety and a first-drive checklist. No coding needed.

How to Make an RC Car at Home: Parts List, Wiring, and 2.4GHz Remote Setup - Cover image

How to Make an RC Car at Home: Parts List, Wiring, and 2.4GHz Remote Setup

To make an RC car at home, we need five things: a chassis with wheels, a drive motor with an ESC (or an RC motor driver) to control its speed, a steering servo, a battery, and a 2.4GHz transmitter and receiver. We can start from a DIY kit or pick every part ourselves.

This guide takes the second road and builds a hobby-grade car: a pistol-grip FlySky remote, a real steering servo, and smooth, proportional throttle. No phone, no app and no code. If you would rather drive from your phone with an Arduino, our Bluetooth-controlled car with Arduino and HC-05 post covers that route step by step.

DIY RC car built at home with a 2.4GHz pistol-grip transmitter

Components and Supplies

FlySky FS-GT2 Transmitter + FS-GR3E Receiver – FPV drone remote for quadcopters. -RobocrazeFlySky FS-GT2 Transmitter + FS-GR3E Receiver – FPV drone remote for quadcopters. -Robocraze

Flysky FS-GT2 Transmitter with FS-GR3E Receiver for RC Car/Boat/Planes/Truck/Quadcopters

Flysky FS-GT2 Transmitter with FS-GR3E Receiver for RC Car/Boat/Planes/Truck/Quadcopters When using a drone, a transmitter is one of the most important components. You can’t run any car/Boat without it because it uses radio signals to send commands wirelessly to a Radio Receiver, which is...
Rs 2,694/-
Rs 2,694/-
Rs 2,915/-
Save Rs 221/-
FlySky FS-CT6B 6CH 2.4GHz Transmitter & Receiver – FPV drone remote for quadcopters. -RobocrazeFlySky FS-CT6B 6CH 2.4GHz Transmitter & Receiver – FPV drone remote for quadcopters. -Robocraze

    FlySky FS-CT6B 6ch 2.4GHz Transmitter & FS-R6B Receiver

    FlySky FS-CT6B 6ch 2.4GHz Transmitter & Receiver FlySky CT6B 2.4Ghz 6 Channel Transmitter with FS-R6B Receiver Remote is the popular 6 Channel Radio.  This 6 Channel Transmitter and Receiver is an entry-level 2.4 GHz radio system offering the reliability of 2.4 GHz signal technology...
    Rs 4,012/-
    Rs 4,012/-
    Rs 4,599/-
    Save Rs 587/-
    TowerPro MG996R Servo Motor 180 Degree with Metal Gear - RobocrazeTowerPro MG996R Servo Motor 180 Degree with Metal Gear - Robocraze

      MG996R Metal Gear Servo Motor - 180 Degree

      MG996R Metal Gear Servo Motor 180 Degree Presenting the durable TowerPro MG996R High-Torque Servo Motor, an excellent choice for robotics and electronics applications. This DC servo motor produces 9.4 kg/cm of torque at 4.8V and 11 kg/cm of torque at 6V, operating efficiently in...
      Rs 399/-
      Rs 399/-
      Rs 449/-
      Save Rs 50/-
      12V 500 RPM DC Rectangle Gear Motor with ​High Torque -Motors & Mechanical -Rectangle Geared Motor -Robocraze12V 500 RPM DC Rectangle Gear Motor with ​High Torque -Motors & Mechanical -Rectangle Geared Motor -Robocraze

        12V 500 RPM DC Rectangle Gear Motor with High Torque

        12V 500 RPM DC Rectangle Gear Motor with High Torque The 12V 500 RPM DC Rectangle Gear Motor with High Torque is a powerful and reliable DC gear motor designed for demanding robotics and automation projects. With its 500 RPM gear motor capability and...
        Rs 1,199/-
        Rs 1,199/-
        Rs 1,520/-
        Save Rs 321/-
        SmartElex 10D Dual Channel Motor Driver Powered by Raspberry PiSmartElex 10D Dual Channel Motor Driver Powered by Raspberry Pi

          SmartElex 10D Dual Channel Motor Driver Powered by Raspberry Pi

          SmartElex 10D Dual Channel Motor Driver Powered by Raspberry Pi The SmartElex 10D Smart Motor Driver is a powerful dual-channel motor driver designed to control brushed DC motors with precision and efficiency. It supports both PWM and RC control modes, making it ideal for robotics,...
          Rs 1,459/-
          Rs 1,459/-
          Rs 2,199/-
          Save Rs 740/-
          LM2596 DC-DC Buck Converter Module – LM2596 step-down converter for stable power. -Power Converter -RobocrazeLM2596 DC-DC Buck Converter Module – LM2596 step-down converter for stable power. -Power Converter -Robocraze

            LM2596 DC-DC Buck Converter Adjustable Step Down Power Supply Module

            LM2596 DC-DC Buck Module The LM2596 DC-DC buck converter is a highly efficient step-down switching regulator capable of driving a 3A output load with excellent line and load regulation. Operating at a 150kHz switching frequency, this LM2596 module allows for smaller filter components compared...
            Rs 62/-
            Rs 62/-
            Rs 99/-
            Save Rs 37/-
            🏆 Best seller
            11.1V 2200mAh 35C 3S1P Bonka Lipo Battery -Batteries & Power Supply -Lipo Batteries & Chargers -Robocraze11.1V 2200mAh 35C 3S1P Bonka Lipo Battery -Batteries & Power Supply -Lipo Batteries & Chargers -Robocraze

              11.1V 2200mAh 35C 3S1P Bonka Lipo Battery

              11.1V 2200mAh 35C 3S1P Bonka Lipo Battery The Bonka 11.1V 2200mAh 35C 3S LiPo Battery for drones is a little powerhouse with a large 2200mAh capacity that operates at 11.1V, which provides the dependability and longevity you need for high-flying adventures. What actually differentiates...
              Rs 2,139/-
              Rs 2,139/-
              Rs 2,567/-
              Save Rs 428/-
              🏆 Best seller
              iMax B6AC Smart Balance Charger 80W – High-performance 80W balance charger. -Battery Charger -RobocrazeiMax B6AC Smart Balance Charger 80W – High-performance 80W balance charger. -Battery Charger -Robocraze

                iMax B6AC Smart Balance Charger 80W

                iMax B6AC Smart Balance Charger 80W The IMAX B6 80W 6A Charger/Discharger 1-6 Cells is a highly advanced charger that boasts the ability to charge, balance, and discharge various types of batteries including LiIon, LiPoly, LiFe (A123), NiCd, and NiMH. This original imax b6ac...
                Rs 1,948/-
                Rs 1,948/-
                Rs 3,499/-
                Save Rs 1,551/-
                XT60 Connector Pair – Secure XT60 connectors for battery & power supply. Electronic Components - RobocrazeXT60 Connector Pair – Secure XT60 connectors for battery & power supply. Electronic Components - Robocraze

                  XT60 Connector Male Female Pair

                  XT60 Connector Male Female Pair Our XT60 Connectors are the perfect solution for your connectivity needs. Measuring 3.5mm and suitable for a wide age range of users, these connectors are designed for both durability and ease of use. These yellow connectors are not only...
                  Rs 29/-
                  Rs 29/-
                  Rs 49/-
                  Save Rs 20/-
                  Cytron 10Amp 7V-30V Dual Channel DC Motor Driver for R/C -Motors & Mechanical -Motor Drivers -RobocrazeCytron 10Amp 7V-30V Dual Channel DC Motor Driver for R/C -Motors & Mechanical -Motor Drivers -Robocraze

                  Cytron 10Amp 7V-30V Dual Channel DC Motor Driver for R/C

                  Cytron 10Amp 7V-30V Dual Channel DC Motor Driver for R/C The Cytron 10Amp 7V-30V Dual Channel DC Motor Driver for R/C (MDDRC10) is a high-performance RC motor driver dual channel solution ideal for R/C vehicles or mobile robots, especially where no microcontroller is used....
                  Rs 3,699/-
                  Rs 3,699/-
                  Rs 4,999/-
                  Save Rs 1,300/-
                  Radiolink R4FGM 2.4GHz Long Range 4 Channel RC Receiver for RC Car with GyroRadiolink R4FGM 2.4GHz Long Range 4 Channel RC Receiver for RC Car with Gyro

                    Radiolink R4FGM 2.4GHz Long Range 4 Channel RC Receiver for RC Car with Gyro

                    Radiolink R4FGM 2.4GHz Long Range 4 Channel RC Receiver for RC Car with Gyro The Radiolink R4FGM DIY RC Receiver is engineered for precision, stability, and long-range performance. Featuring a pseudo-random FHSS algorithm, it delivers exceptional anti-interference capability with a control range of up...
                    Rs 1,509/-
                    Rs 1,509/-
                    Rs 1,999/-
                    Save Rs 490/-

                    What We Need

                    Every RC car, from a toy to a racing buggy, uses the same five building blocks. The table below lists each one, the job it does, and the part we picked for this build.

                    Part What it does Our pick
                    2.4GHz transmitter + receiver Sends steering and throttle from our hand to the car FlySky FS-GT2 transmitter with FS-GR3E receiver
                    Steering servo Turns the front wheels left and right MG995 metal gear servo
                    Drive motor Spins the rear wheels 12V 500 RPM high-torque geared DC motor
                    ESC (RC motor driver) Turns the receiver's throttle signal into motor speed, direction and braking SmartElex 10D dual-channel motor driver (PWM + RC input)
                    Servo power (BEC) Gives the servo and receiver a clean 5 to 6V supply LM2596 DC-DC buck converter
                    Battery Powers everything 11.1V 2200mAh 35C 3S LiPo (Bonka, XT60)
                    Charger Balance-charges the LiPo safely iMax B6AC 80W balance charger
                    Connector Joins the battery to the car's power lead XT60 male connector with wire
                    Chassis Holds everything, with steerable front wheels Car chassis with a steering linkage, from our DIY RC car kits

                    The Cytron MDDRC10 RC motor driver plugs straight into an RC receiver and can mix throttle and steering for tank-style cars without a servo. And if we prefer a slower, lighter, crawler, the 12V 200 RPM Johnson geared motor is a lighter, cheaper option.

                    Two Routes: Arduino + Bluetooth vs Hobby-Grade 2.4GHz

                    There are two common ways to build an Arduino RC car or its hobby-grade cousin. Both work. They suit different goals.

                    Feature Arduino + Bluetooth Hobby-grade 2.4GHz
                    Controller Phone app over Bluetooth Pistol-grip transmitter
                    Brain on the car Arduino Uno + HC-05 module None. The receiver drives the servo and ESC directly
                    Steering Skid steering (one side slows down) Servo turns the front wheels
                    Throttle Steps set in the app Proportional trigger, smooth from crawl to full
                    Typical range About 10m 100m or more in open ground
                    Coding Yes, an Arduino sketch None
                    Best for Learning code and electronics Driving outdoors, speed and real RC feel

                    The Bluetooth route is the better classroom project, and our Bluetooth car guide walks through it. The HC-05 uses classic Bluetooth, which iPhones cannot connect to, so that route is Android-only unless we swap in a BLE module.

                    The hobby-grade route skips code completely. A dedicated transmitter and receiver pair talks on its own 2.4GHz link, hops frequencies to dodge interference, and feels like a real RC car from the first trigger pull. The rest of this guide builds that version.

                    Step by Step: Chassis, Motor, ESC, Servo, Receiver

                    We build from the ground up: mechanics first, then power, then signals. Keep the battery unplugged until the last step.

                    1. Prepare the chassis

                    We need a frame with a steerable front axle and a driven rear axle. A car-style kit chassis or an old toy RC car with a broken remote both work well. A flat robot chassis with a castor wheel will not work here: the servo has no front axle to turn, so pick a chassis with a steering linkage. Check that the front wheels swing freely from lock to lock before adding any electronics.

                    2. Mount the RC car motor

                    Bolt the geared motor to the rear axle mount, then fit the wheel or drive gear to its 6mm shaft. A geared motor matters here: a bare motor spins far too fast to push a car without a gearbox.

                    As a rough guide, a 500 RPM motor turning 85mm wheels gives about 8 km/h; a 200 RPM motor gives about 3 km/h with more pulling power.

                    3. Fit the ESC (motor driver)

                    The ESC sits between the battery and the motor and reads the throttle channel from the receiver. Our ESC guide explains how one works in detail.

                    For a brushed DC motor like ours, an RC-input motor driver does the ESC's whole job: forward, reverse, and braking. Avoid drone ESCs such as the SimonK 30A for this. They drive brushless motors in one direction only, so the car would have no reverse.

                    Connect the battery leads to the driver's power input and the motor's two wires to its Motor 1 output. Then set the driver to RC input mode as its manual describes.

                    4. Install the RC car steering servo

                    Screw the MG995 into the chassis so its output shaft sits near the centre of the steering link. Before fitting the horn, power the servo from the receiver and centre the steering trim on the transmitter; the servo moves to its centre. Now fit the horn pointing straight ahead and connect it to the steering link.

                    The MG995 gives about 10 kg-cm at 4.8V, plenty for a car of this size. A 25T metal servo horn is a worthwhile upgrade over the plastic one.

                    5. Wire the receiver and servo power

                    The FS-GR3E has three channels. On FlySky surface radios, channel 1 is steering and channel 2 is throttle.

                    CH1 → servo (signal, + and −)
                    CH2 → ESC's RC input (signal and −)
                    CH3 → 5.5V from the LM2596 buck converter, which powers the receiver and servo

                    Set the LM2596 to 5.5V with a multimeter before plugging anything into it. It feeds both the receiver and the servo, because a servo can pull about 2A when it stalls; a weaker supply makes the receiver brown out and lose the link. If the ESC's RC lead also carries 5V, remove its red wire so only one regulator feeds the receiver.

                    DIY RC car wiring diagram

                    Binding the Transmitter and Receiver

                    Binding pairs the receiver to one transmitter's unique ID, so the car listens to our remote and ignores every other 2.4GHz signal nearby. The FS-GT2 and FS-GR3E ship unbound, with a bind plug in the box.

                    1. Load fresh batteries into the transmitter and keep it switched off.
                    2. Push the bind plug into the receiver's BIND port.
                    3. Power the car. The receiver LED flashes fast: it is waiting to bind.
                    4. Hold the transmitter's BIND button and switch the transmitter on.
                    5. When the receiver LED stops flashing and stays lit, release the button. Binding is done.
                    6. Pull out the bind plug, switch both off, then power the transmitter first and the car second.

                    The idea is the same on every FlySky radio, and our FlySky FS-i6 binding guide shows each step with photos. Check the exact button names against the FS-GT2 manual in the box. Still choosing a radio? Our guide to the best RC car transmitter and receiver in India compares the FS-GT2, Radiolink sets and gyro receivers.

                    After binding, test the failsafe. With the wheels off the ground, give a little throttle and switch the transmitter off. The motor must stop. If it keeps running, set the failsafe as the manual describes before the first drive.

                    A note on the Radiolink R4FGM. The Radiolink R4FGM 4-channel receiver with gyro is a popular upgrade, and its built-in gyro helps hold the car straight. It binds only to Radiolink transmitters such as the RC4GS, RC6GS, RC8X, T8FB, and T8S, not to FlySky radios. Pick the receiver to match the transmitter brand.

                    Choosing the Battery (Li-ion vs LiPo, Voltage)

                    For this build, the right RC car battery is a 3S 11.1V LiPo. It matches the 12V motor and stays above the motor driver's 7V minimum even when nearly empty.

                    Each lithium cell is 3.7V nominal and 4.2V when full, so the cell count (the "S") sets the pack voltage:

                    Pack Nominal Full charge Good match for
                    2S 7.4V 8.4V 6V motors, small Arduino cars
                    3S 11.1V 12.6V 12V motors, this build
                    4S 14.8V 16.8V Brushless high-speed cars

                    A 2S pack would run our 12V motor at about two-thirds speed and sag below 7V under load, which makes the driver cut out.

                    Li-ion or LiPo? Li-ion 18650 cells are cheaper, last more charge cycles, and suit gentle loads such as an Arduino car. LiPo packs are lighter and deliver much higher current, which a motor needs when it accelerates or climbs. The C-rating tells us how much: our 2200mAh 35C pack can supply 2.2A × 35 = 77A, far more than this car will ever draw.

                    Capacity sets run time. 2200mAh gives roughly 15 to 25 minutes of mixed driving with this motor.

                    Battery safety: read before the first charge

                    • Charge only in the iMax B6AC's LiPo BALANCE mode, with the balance lead plugged in. Never use NiMH mode for a LiPo.
                    • Charge at 1C or less: 2.2A for a 2200mAh pack.
                    • Never charge unattended. Use a fireproof LiPo bag on a non-flammable surface.
                    • Stop driving when the car slows. Do not run a cell below about 3.2V.
                    • Store packs at about 3.8V per cell (about 11.4V for 3S) using the charger's Storage mode.
                    • Retire any pack that swells, gets hot, smells or has a damaged wrap.

                    Our LiPo battery safety guide covers charging, storage and disposal in full.

                    First Drive Checklist and Common Problems

                    Run through this list with the wheels lifted off the ground before the first drive.

                    • ☐ Battery fully balance-charged and plugged in the right way round
                    • ☐ LM2596 output measured at 5.5V before the receiver was connected
                    • ☐ Transmitter on first, car second; receiver LED solid
                    • ☐ Steering centred with the trim, and full lock both ways without the servo buzzing
                    • ☐ Trigger pulled: wheels go forward; pushed: brake, then reverse
                    • ☐ Transmitter switched off: motor stops (failsafe works)
                    • ☐ No loose wires near the wheels or gears
                    Problem Likely cause Fix
                    Nothing responds Receiver not bound, or no power on its rail Check the receiver LED, then rebind
                    Steering works, motor does not ESC not in RC mode, or CH2 lead on the wrong pins Recheck the driver's mode setting and RC input wiring
                    Steering is reversed Servo direction Reverse CH1 in the transmitter's settings
                    Car drives backwards on throttle Motor wires swapped Swap the two motor wires, or reverse CH2
                    Car creeps with the trigger released Throttle trim off centre Centre the throttle trim, then power-cycle the ESC so it recalibrates
                    Receiver resets when steering hard Servo pulling too much current Power the servo from the LM2596 as shown, not from a weak 5V pin
                    Short range or glitches Antenna blocked or bent Route the receiver antenna up a straw, away from the motor and battery
                    Car cuts out after a few minutes Battery low or driver too hot Charge the pack; give the driver airflow

                    Prefer a kit? Browse DIY RC car kits

                    Not ready to source every part? Our DIY RC car kits range has chassis, motors and complete car kits for every level, from first builds to ESP32 smart cars. Start with a kit, then add the 2.4GHz radio from this guide when you want real RC control.

                    Browse DIY RC car kits →

                    Excerpt

                    Learn how to make an RC car at home with our parts list, wiring diagram and 2.4GHz transmitter setup. Covers ESC, steering servo, battery and binding.

                    Frequently Asked Questions

                    1. What parts do we need to make an RC car?

                    We need a chassis with wheels, a drive motor, an ESC or RC motor driver, a steering servo, a battery and a 2.4GHz transmitter and receiver. Add a balance charger if the battery is a LiPo, plus connectors and a small buck converter to power the servo cleanly.

                    2. Can we make an RC car with Arduino?

                    Yes. An Arduino Uno with an L298N motor driver and an HC-05 Bluetooth module makes a phone-controlled car, as our Bluetooth car guide shows. An Arduino can also read a 2.4GHz receiver or an NRF24L01 radio for custom features such as lights, sensors or speed limits.

                    3. Which motor is best for an RC car?

                    For a first build, a geared brushed DC motor is the easiest choice: cheap, simple to drive and strong at low speed. Pick the RPM for the speed we want. Brushless motors are faster and more efficient, but they need a brushless car ESC with reverse.

                    4. Do we need an ESC?

                    Yes, or a motor driver that does the same job. The receiver only outputs a low-power signal, so something must turn it into motor current with speed, direction and braking. For brushed motors an RC-input motor driver works; brushless motors need a brushless ESC.

                    5. How do we bind a transmitter to a receiver?

                    Insert the bind plug into the receiver, power it until its LED flashes fast, then hold the transmitter's bind button while switching it on. When the LED goes solid, remove the plug and power-cycle both. The transmitter and receiver must be the same brand.

                    6. Which battery is best for an RC car?

                    Match the battery voltage to the motor first: a 3S 11.1V LiPo suits 12V motors, a 2S 7.4V pack suits 6V ones. LiPo gives the high current a car needs; Li-ion 18650 packs are fine for gentle Arduino cars. Always balance-charge LiPos with a proper charger.

                    7. How far can a 2.4GHz RC car go from the transmitter?

                    A basic 2-channel FlySky set like the FS-GT2 typically reaches 100m or more in open ground, depending on obstacles and how the antenna is routed. Bluetooth cars usually manage about 10m. For longer range, keep the receiver antenna upright and away from metal and wiring.

                    8. How fast will a homemade RC car go?

                    It depends on motor RPM and wheel size. Speed in km/h is roughly RPM × wheel diameter in mm × 0.00019, so a 500 RPM motor with 85mm wheels gives about 8 km/h. A higher-RPM motor, a bigger wheel or a brushless setup raises top speed.

                    Prev Post
                    Next Post

                    Leave a comment

                    Please note, comments need to be approved before they are published.

                    Thanks for subscribing!

                    This email has been registered!

                    Shop the look

                    Choose Options

                    Edit Option
                    Back In Stock Notification
                    Compare
                    Product SKU Description Collection Availability Product Type Other Details

                    Choose Options

                    this is just a warning
                    Login
                    Shopping Cart
                    0 items
                    FREE SHIPPING!
                    ₹100 OFF
                    ₹200 OFF
                    ₹999
                    ₹2500
                    ₹4900
                    WhatsApp Chat Chat