Official Raspberry Pi 4 Model B 4GB RAM Development Board
10K Pot Potentiometer - (Pack of 5)
Let us know!
We'll try to match the price for you
Couldn't load pickup availability
The 10K potentiometer is a three-terminal variable resistor used to adjust resistance or divide voltage in electronic circuits. With a nominal resistance of 10,000 ohms (10kΩ), this component is suitable for DIY electronics, Arduino experiments, robotics projects, and circuit prototyping. This pack includes five 10K pot potentiometers for use across multiple projects.
A potentiometer contains a resistive track and a movable contact called a wiper. Turning the shaft moves the wiper along the track, changing the resistance between the centre terminal and either outer terminal. When connected as a voltage divider, the wiper provides an adjustable output voltage that can be read by a microcontroller or used as a control input.
Ready to bring your circuits to life? Pair this component with our complete Arduino Kits and start building today.
The three terminals serve different purposes when the component is used as a voltage divider:

The two outer terminals connect to opposite ends of the resistive track, while the centre terminal connects to the wiper. Reversing the outer connections changes the direction in which the output voltage rises as you turn the shaft. Confirm the terminal arrangement for your specific component before wiring it.
The term B10K potentiometer commonly refers to a 10kΩ potentiometer with a linear taper. In a linear-taper potentiometer, the resistance ratio changes approximately in proportion to the shaft's rotation. This makes it useful for applications such as sensor adjustment, analog input experiments, and general circuit prototyping. Check the product's markings or datasheet before assuming its taper, as the taper is not confirmed by the nominal resistance value alone.
You can connect a 10K potentiometer to an Arduino to create a simple adjustable analog input.
Upload this example to read the potentiometer position:
const int potPin = A0;
void setup() {
Serial.begin(9600);
}
void loop() {
int potValue = analogRead(potPin);
Serial.println(potValue);
delay(100);
}
On a typical 10-bit Arduino ADC, analogRead() returns a value from 0 to 1023, depending on the wiper voltage. The reading changes as you turn the shaft. ADC resolution and permitted input voltage vary by board, so use the correct supply and input limits for your Arduino.
A 10K potentiometer can be used for adjustable voltage dividers, analog control inputs, sensor calibration, robotics experiments, DIY electronics kits, and prototyping circuits. It is intended for low-power signal and control applications unless the component's power rating confirms suitability for other uses.
This pack of five is a practical option for students, hobbyists, and makers building Arduino-based projects and experimenting with variable resistance.
| Resistance | 10K Ohm |
| Potentiometer Type | Pot Potentiometer |
| Material | Carbon Film and Metal |
| Interface | 3 Pin |
| Shaft Length | 15mm |
| Dimensions | 1 x 1 x 1cms |
| Weight | 15 grams |
A potentiometer is a type of variable resistor that is used to adjust the resistance in an electrical circuit. It consists of a resistive element, a sliding contact (wiper), and two terminals. By adjusting the position of the wiper, the resistance between the two terminals can be varied. A 10k potentiometer is a potentiometer with a resistance of 10,000 ohms (10k ohms). The resistance of a potentiometer is typically expressed in ohms, and it is represented by the letter "R" in electrical formulas. Potentiometers are commonly used in a variety of applications, including volume control, tone control, and light dimming. They are often used as a simple way to adjust the resistance in a circuit without using a separate resistor.
The current handling capability of a potentiometer depends on several factors, including the type of potentiometer, the size and material of the resistive element, and the size and type of the wiper. In general, the current handling capability of a potentiometer is limited by the size and material of the resistive element and the wiper. The resistive element and wiper are designed to handle a certain amount of current before they start to heat up and potentially fail. A 10k potentiometer is a relatively low-power component, and it is typically not designed to handle high levels of current. As a general rule of thumb, it is recommended to keep the current through a potentiometer below 1 milliampere (mA) to ensure that it does not overheat and fail.
A 10k potentiometer is a type of variable resistor that is used to adjust the resistance in an electrical circuit. The "10k" in the name refers to the resistance of the potentiometer, which is 10,000 ohms (10k ohms). The resistance of a potentiometer is typically expressed in ohms, and it is represented by the letter "R" in electrical formulas. Potentiometers are commonly used in a variety of applications, including volume control, tone control, and light dimming. They are often used as a simple way to adjust the resistance in a circuit without using a separate resistor. To use a potentiometer, it is typically connected in series with a circuit, and the wiper is adjusted to vary the resistance between the two terminals. The resistance of the potentiometer can be calculated using the following formula:
The "10K" indicates a maximum resistance of 10,000 ohms. The "B" denotes a linear taper, meaning the resistance increases at a steady, linear rate as the shaft is rotated, making it ideal for precise measurement and control applications.
You can check the current 10k ohm potentiometer price and bulk availability directly on this Robocraze product page. We offer competitive pricing and a pack of 5 to ensure you have spares for all your prototyping needs.
Yes! While the Raspberry Pi lacks native analog inputs, you can use an ADC (like the MCP3008) to read this 10k pot. For the ESP32, you can connect the wiper directly to any of its built-in ADC pins, just like with an Arduino.
Erratic analog readings are usually caused by loose breadboard connections, electrical noise, or dust on the internal resistive track. First, ensure the pins are firmly seated. If the issue persists, adding a small decoupling capacitor (e.g., 0.1µF) between the wiper (middle pin) and Ground can smooth out the signal. You can also average multiple analogRead() samples in your code for a more stable value.
The primary difference is the maximum resistance. A 10k pot maxes out at 10,000 ohms, while a 100K pot maxes out at 100,000 ohms. For most standard microcontroller projects (like reading a dial position or setting a reference voltage), a 10k ohm potentiometer is the ideal industry standard. It draws minimal current while still providing a strong, noise-resistant signal to analog pins compared to higher resistance values.
This standard single-turn potentiometer typically has a power rating of 0.15W (150mW) to 0.25W. It is specifically designed for low-power signal control, voltage division, and analog input reading. It should not be used to directly drive high-power loads like motors, heaters, or high-brightness LEDs; always use a transistor, MOSFET, or motor driver for those applications.
This is a standard single-turn potentiometer. It provides the full resistance range (0 to 10K ohms) within approximately a 270 to 300-degree rotation of the shaft. This makes it perfect for quick, intuitive, and user-facing manual adjustments in DIY electronics, robotics, and audio projects, unlike multi-turn trimmer pots which are meant for fine, infrequent calibration.